The KILN P Series can cook a 13" pizza and can fit various cast iron cookware. The mouth of the KILN P Series is 3.46in | 88mm high, we recommend not using bakeware and cookware higher than 1.9in | 50mm.

No, accessories are sold separately.

4 x AA batteries - 1 x for ignition and 3 x for turntable and display.

Remove all packaging and recycle as per your local government laws. Place the KILN on the Pizza Station or similar benchtop. Insert the center stone.
To install the batteries, open the battery compartment cover. Load a set of 3 new AA type batteries into the battery box, ensuring the plus (+) and minus (-) ends are in the correct position, then refit the cover. Unscrew the pulse igniter cap to fit one new AA type battery, ensuring the plus (+) and minus (-) ends are in the correct position, then refit the cap. Close the battery compartment cover.
Make sure the burner knob is turned off, then connect the gas hose and regulator for LPG / propane cylinder use or the propane canister regulator. In the EU, butane is used and will require 2 x butane canisters with the dual connector. The KILN can only be used in an above-ground open-air environment with natural ventilation. DO NOT use the KILN indoors.

We recommend placing your KILN P Series on a heat-resistant surface, such as metal or stone. We highly recommend NOT placing your KILN on glass, plastic, or fabrics e.g. tablecloths

Flame Safeguard System - The gas valve on this appliance has a flame safeguard built in for added safety; when gas flow is stopped in the event the flame is extinguished without using the control knobs

We don’t recommend using the KILN P Series in adverse weather conditions, and suggest reviewing your local forecast before cooking. If cooking in windy conditions it is recommended to face the KILN P out of direct wind.

• Wear heatproof gloves when handling hot dishes
• Use caution when inserting & removing dishes from the KILN.
• Avoid contacting the front fascia surface as minor scratches may occur
• Use caution with the stones - they can retain heat for many hours after cooking.
• Do NOT submerge the stone in water
  

Prior to cooking for the first time, turn the burner on high for 30 minutes, then turn off and let the oven cool down. Once cool, use a paper towel to wipe away any soot inside. Be careful, the oven may still be hot in some places.
Push the burner knob in and slowly turn it anti-clockwise until you hear it click (8-10 seconds). Hold in for another 10 seconds after ignition, then release. Set the burner to your desired position.
Press the rotate button to activate the rotating turntable and power button to active the screen.
If the Infrared burner does not ignite, leave the knob at OFF and wait 5 minutes before trying again.
Once ignited, leave on high for approximately 15 minutes to heat the stone.
The KILN is ready to use once it has reached your desired temperature. To check this simply refer to the digital display. When inserting your pizza, turn off the rotate button, once launched turn the main burner knob halfway and reactivate the rotate button. Then begin cooking.

Refer to your instruction manual that was supplied in your box or contact your local dealer.

Refer to your instruction manual that was supplied in your box or contact your local dealer.

Refer to your instruction manual that was supplied in your box or contact your local dealer.

Always allow the KILN P Series and stones to cool completely before cleaning—they may take up to 1 hours to cool and can retain heat for many hours.
Clean the exterior with mild detergent and a clean cloth, then dry thoroughly. Clean the interior using warm soapy water and a sponge or mild scourer. For stubborn marks, apply a gentle bicarbonate soda paste. Avoid phosphoric-based cleaners, as they may damage the finish.
To clean the burners and ignition, use a soft-bristle brush to carefully clear debris.
The pizza stones are not dishwasher safe. Brush away food particles using a Pizza Oven Brush or similar, wipe with water, and dry completely.
Do NOT submerge the stones in water.

After each use, cool and clean the KILN before fitting the protective cover. The cover is made from heavy-duty water-resistant material, but for best longevity, store your KILN P under cover and in a dust-free environment.
During extended periods of non-use, occasionally wipe internal and external surfaces to prevent dust and moisture build-up.

Basic Troubleshooting information on the KILN P Series can be found within the user manual.

Please contact your local dealer or our customer care team via the 'Contact Us' form.

Turn it down. Running the appliance for an extended period of time with the burner on the high setting could result in damage to your appliance

Check to see if; the cylinder valve is on, the cylinder is full of gas, the battery is correctly placed in the ignition slot, and the batteries are fully charged. Please contact your local service center/dealer if all of the above are ok.

The appearance of the KILN may change over a period of time, depending on the climate conditions, usage of the oven and how well it has been maintained by the user.

Check your gas bottle and connection, and ensure you’re following the correct ignition procedure.
Windy conditions may weaken or extinguish the burner. After checking all connections and retrying ignition, contact customer care or your local dealer if the issue persists.

Check if batteries are fitted and are properly installed in the battery compartment. Check if batteries are full of charge and replace if needed. If you have any further issues please contact your local service center or dealer